Energy Machinery, Inc. - New England's Compressed Air Specialists
Energy Machinery, Inc.
10 Reservoir Park Drive
Rockland, MA 02370
Toll Free: 1-800-643-4330
Phone: 781-871-6220
Fax: 781-878-7085
Email: info@energymachinery.com
Website: www.energymachinery.com
Print Back
The Champion ATLE6 is a single stage, two cylinder, pressure lubricated compressor that is equipped with an SAE#3 bell housing flange for direct engine mounting and remote site operation.
Unit of Measure

Specifications

Motor Power

 N/A 29 hp22 kW

Number of Cylinders

 N/A 2

Speed at 29 hp (22 kW) Power

 N/A 1550 rpm

Piston Displacement

 N/A 262 ft³/min7.8 m³/min

Oil Capacity

 N/A 9 liq qt8.5 L

Maximum Pressure

 N/A 30 psig2.07 bar

Discharge Air Temperature

 N/A 400 ºF204 ºC

Duty Cycle

 N/A Intermittent

Flow

 N/A 180 ft³/min5.1 m³/min

Industry Standards/Certifications

 N/A Compressed Air and Gas Institute (CAGI) Energy Star Partner ISO 9001:2008

Dimensions

Bore Diameter

 N/A 7.875 in200 mm

Stroke

 N/A 3 in76 mm

Suction and Discharge Pipe Size

 N/A 3 in

Inlet Port Design

 N/A NPT

Discharge Port Design

 N/A NPT

Length

 N/A 41 in1041 mm

Width

 N/A 29 in737 mm

Height

 N/A 30 in762 mm

Weight

 N/A 750 lb340 kg

Lubrication

Lubrication

 N/A
  • Superior lubrication is accomplished through a gear driven oil pump powered by the crankshaft.
  • Pressurized system ensures complete lubrication to the crankshaft, connecting rods, bearings and piston pins.
  • Full flow, spin-on oil filter ensures impurities are removed before the lubricant contacts any internal components.
  • Oil pressure gauge is conveniently mounted to display the oil pressure.

Valves

Valves

 N/A
  • Concentric ring design incorporates both the inlet and outlet valves in one assembly.
  • Designed to give 100% exposure to the air flow for maximum efficiency (i.e. more CFM per HP).
  • Discs and springs are made of AISI 420 stainless steel to give dependable corrosion-free and fatigue-free service life.

Standard Features

Standard Features

 N/A
  1. ASME pressure relief valve protects the intercooler and first stage from over pressure.
  2. Suction unloading valves (where applicable) provide load less starting and stopping as well as quick response to capacity demands.
  3. Removable hand-hole plate allows easy access to the internal running gear.
  4. Tri-Metal insert bearings are two-piece for quick and easy replacement.
  5. Counterbalanced crankshaft assures smooth operation.
  6. Replaceable piston pin bearings are very economical when replacement becomes necessary.
  7. Deep-finned cylinders and heads quickly dissipate the heat of compression.
  8. Crankshaft ends are supported by large tapered roller bearings for smooth operation and long life.
  9. Oil pressure gauge assures the operator of lubrication system integrity.
  10. The cylinders and crankcase are built of industrial strength cast iron materials.
  11. Continuous Operation

Additional Information

Additional Information

 N/A Wherever there's a demand for a low pressure engine driven compressor, the ATLE6 is the compressor for the job. Because it is direct coupled to the engine, there is no need to worry about belts slipping or wearing out. When connected to the engine, all rotating components are totally enclosed and protected from the environment.

Low Pressure Bare
Factory Fill with ChampLub 500